lvgl_esp32_drivers/lvgl_i2c/Kconfig

menu "I2C Port 0"

	config I2C_MANAGER_0_ENABLED
		bool "Enable I2C port 0"
		
	if I2C_MANAGER_0_ENABLED
		config I2C_MANAGER_0_SDA
			int "SDA (GPIO pin)"
			default 0
		config I2C_MANAGER_0_SCL
			int "SCL (GPIO pin)"
			default 0
		config I2C_MANAGER_0_FREQ_HZ
			int "Frequency (Hz)"
			default 400000
			range 100000 5000000
			help
				The clock speed in Hz. Ranges from 100000 (100 kHz) to
				5000000 (5 Mhz). I2C busses that involve external wires may
				have to be slower, and the real maximum speed the bus will
				support depends on the value of the pullup resistors and the
				design of the overall circuit. 
		config I2C_MANAGER_0_TIMEOUT
			int "R/W timeout (ms)"
			default 20
			range 10 1000
			help
				Timeout for I2C read and write operations. This does not
				include the time waiting for a lock.
		config I2C_MANAGER_0_LOCK_TIMEOUT
			int "Stale lock override (ms)"
			default 50
			range 10 1000
			help
				Timeout at which point an operation waiting for its turn on
				the port will assume that whatever set the lock has died and
				overrides it. Set this somewhat larger than the previous
				timeout.
		config I2C_MANAGER_0_PULLUPS
			bool "Use ESP32 built-in bus pull-up resistors"
			help
				The I2C bus needs resistors to make sure it's in a defined
				state when nobody is talking. Many circuits have external
				pullup resistors already and turning these on will increase
				power consumption slightly and may limit the speed your bus
				can attain. Try with these off first if you don't know.
	endif

endmenu


menu "I2C Port 1"
	
	config I2C_MANAGER_1_ENABLED
		bool "Enable I2C port 1"
		
	if I2C_MANAGER_1_ENABLED
		config I2C_MANAGER_1_SDA
			int "SDA (GPIO pin)"
		config I2C_MANAGER_1_SCL
			int "SCL (GPIO pin)"
		config I2C_MANAGER_1_FREQ_HZ
			int "Frequency (Hz)"
			default 1000000
			range 100000 5000000
			help
				The clock speed in Hz. Ranges from 100000 (100 kHz) to
				5000000 (5 Mhz). I2C busses that involve external wires may
				have to be slower, and the real maximum speed the bus will
				support depends on the value of the pullup resistors and the
				design of the overall circuit. 
		config I2C_MANAGER_1_TIMEOUT
			int "R/W timeout (ms)"
			default 20
			range 10 1000
			help
				Timeout for I2C read and write operations. This does not
				include the time waiting for a lock. Default should be fine.
		config I2C_MANAGER_1_LOCK_TIMEOUT
			int "Stale lock override (ms)"
			default 50
			help
				Timeout at which point an operation waiting for its turn on
				the port will assume that whatever set the lock has died and
				overrides it. Set this somewhat larger than the previous
				timeout. Default should be fine.
			range 30 1000
		config I2C_MANAGER_1_PULLUPS
			bool "Use ESP32 built-in bus pull-up resistors"
			help
				The I2C bus needs resistors to make sure it's in a defined
				state when nobody is talking. Many circuits have external
				pullup resistors already and turning these on will increase
				power consumption slightly and may limit the speed your bus
				can attain. Try with these off first if you don't know.
	endif

endmenu